Best Epoxy for Fishing Lures: Top Coats, UV Resins and Clear Coats

14 min read

As an Amazon Associate I earn from qualifying purchases. Read our affiliate disclosure.

The short answer

For a brush-on crankbait top coat, EnviroTex Lite Pour-On High Gloss Finish; for dipping many baits with nothing to mix, KBS DiamondFinish Clear; for a fast cure on jigs and small parts, Alumilite Alumi-UV.

Our verdict

Lure Epoxy Top Picks

A painted crankbait or jig needs a clear top coat for a hard, glossy shell. Lure builders use three kinds: two-part epoxies you brush on, UV-cure resins that harden under a lamp or sunlight, and one-part clear coats you dip. Here are eight from seven brands, each linked at the exact size, with the cure time, working time and mix ratio its maker or listing gives. For finished baits, see our guide to freshwater lures by type, and for rods and reels, browse our fishing gear guides.

Related guide: Best Gear for Trout Fishing: Rod, Reel, Line, Lures and Net

Lure coating finder

Find a top coat for the lures you build

Pick what you are coating and a price tier per container. The suggestion is our editorial starting point among the eight coatings below, drawn from the makers' pages and the sources cited in each review, not a test result.

What are you coating?
Price tier

Tiers are relative to the products in this guide; live prices are in the comparison table below.

Compare the picks

Compare the 8 Lure Top Coats

ENVIRONMENTAL Environmental Technology 16-Ounce Kit Lite…EnviroTex LitePour-On Epoxy Top CoatCrankbaits, brush-onListing: about 72 hours$24.80
Linked size16 oz kit
Mix ratioListing: 1:1
Working timeNot published
UV / yellowing claimNot published

Evidence: listing specs; TackleUnderground owner posts cited in the review

Devcon Epoxy, 2 Ton Epoxy, 4-1/2 Ounce Bottles, 2 BottlesDevcon 2 Ton30-Minute Glue EpoxyCrankbaits, brush-onListing: sets in 30 minutes$21.14
Linked sizeTwo 4.5 oz bottles
Mix ratioNot published
Working timeNot published
UV / yellowing claimNot published

Evidence: listing specs; TackleUnderground owner posts cited in the review

Bob Smith 206 Slow-Cure 9oz EpoxyBob Smith Slow-Cure30-Minute Bulk EpoxySaltwater lures, brush-onMaker: overnight$22.45
Linked size9 oz
Mix ratioMaker: equal parts
Working timeSalty's: 30 minutes
UV / yellowing claimNot published

Evidence: Salty's (saltwaterplugs.com) (a retailer), not independent

Alumilite Amazing Clear Cast Plus 16 Oz, UV Resistant Epoxy…Amazing Clear Cast PlusUV-Resistant Pour EpoxyCrankbaits, brush-onMaker: 3-5 days
Linked size16 fl oz kit
Mix ratioMaker: 1:1
Working timeMaker: 20-25 minutes
UV / yellowing claimMaker: UV-resistant formula

Evidence: Slim Shady Customs, Alumilite “Amazingly Clear” (likely the original Amazing Clear Cast), not the Plus formula

KBS Coatings 8404 DiamondFinish Watercolor Clear Coat - 1…KBS DiamondFinish ClearOne-Part Dipping ClearDipping, jigs, crankbaitsMaker: 7 days$65.00 Prime
Linked size32 fl oz
Mix ratioMaker: no mixing
Working timeListing: no pot life
UV / yellowing claimListing: QUV 313B 1,000 hours

Evidence: Slim Shady Customs, DiamondFinish Clear; can size not stated

ArtResin Epoxy Resin – High-Gloss Clear Coat for Artwork…ArtResin45-Minute Art EpoxyCrankbaits, brush-onMaker: 72 hours$28.00
Linked size8 oz kit
Mix ratioMaker: 1:1
Working timeMaker: about 45 minutes
UV / yellowing claimListing: UV protection

Evidence: maker specs; 2016 TackleUnderground owner posts cited in the review

Alumilite Alumi-UV 4 Oz, Light Cured Resin for Fishing Lure…Alumi-UVUV-Cure Lure ResinJigs, uV cure, small batchesListing: 2-10 minutes$14.99
Linked size4 oz
Mix ratioMaker: no mixing
Working timeListing: until UV exposure
UV / yellowing claimNot published

Evidence: maker specs only, no independent test

Loon Outdoors UV CLEAR FLY FINISH, Flow, 1/2 ozLoon UV Clear Fly FinishThin UV Fly FinishFly heads, uV cureMaker: about 15 seconds$19.95
Linked size1/2 oz
Mix ratioMaker: no mixing
Working timeNot published
UV / yellowing claimNot published

Evidence: maker specs only, no independent test

Prices as of Nov 19, 00:08 UTC

“Not published”: neither the maker nor the Amazon listing we read gives the figure. Cure times are the makers’ own and change with temperature and coat thickness.

How We Chose These Lure Coatings

How this guide was built

built from manufacturer documentation, published third-party reviews and owner reports; we have not tested these products ourselves.

What each coating had to show

  • A lure-making tie: sold for lures by its maker, or used as a top coat by a named lure builder or supplier.
  • The exact size on one Amazon listing, new and in stock on the day of writing.
  • Working and cure figures from the maker or listing, or “not published.”
  • A distinct job: brush-on, dip-on or UV-cure, with a stated trade-off where two overlap.
Sources and their limits

Sources and their limits

Figures come from the makers’ pages and technical data sheets, then the Amazon listings, each labelled. Lure-making context comes from Slim Shady Customs, a custom crankbait maker; Salty’s, a lure-supply shop that sells Bob Smith epoxy (a retailer, not independent); and a 2016 TackleUnderground thread of lure builders. None compared these products side by side. Five of the eight were sold on Amazon by third-party sellers when we checked; each review names the seller.

Lure Epoxies and Clear Coats: Detailed Reviews

Picks: EnviroTex Lite, Devcon 2 Ton, Bob Smith Slow-Cure, Amazing Clear Cast Plus, KBS DiamondFinish, ArtResin, Alumi-UV, Loon UV Fly Finish.

EnviroTex Lite Pour-On High Gloss Finish, Pour-On Epoxy Top Coat

Pour-On Epoxy Top Coat
ENVIRONMENTAL Environmental Technology 16-Ounce Kit Lite…

EnviroTex Lite

16 oz Kit

Crankbait builders who want a high-build, glossy top coat and can turn baits while it levels.

$24.80 from AmazonAs of Nov 19, 00:08 UTC

Verdict

The pour-on coating epoxy TackleUnderground posters keep naming for crankbait top coats.

Evidence: No independent test; maker specs. Source: Amazon listing.

The Amazon listing sells it as a thick single coat: “No need to apply 60 coats of varnish,” it says, and “It cures in 8 hours and reaches full strength and hardness in about 72 hours.” In the TackleUnderground thread, poster mcallister920 writes “Envirotex Lite- the search stops there,” and poster Travis calls it “readily available” and “isn’t too difficult to use.” Poster token12 adds the caveat: “E-tex in my opinion is runny,” with “about 8 hours to harden and 48-72 hours for a full cure.”

EnviroTex Lite, ArtResin or Amazing Clear Cast Plus? All three are 1:1 coating epoxies. EnviroTex Lite has the lure-forum following; ArtResin lists about 45 minutes of working time; Amazing Clear Cast Plus publishes a full data sheet and a UV-resistant formula.

Specs (linked: 16 oz kit)

    Pros

    • One thick coat in place of many coats of varnish, per the listing
    • Named by several TackleUnderground lure builders

    Cons

    • Runny, per one poster; poster BobP says coated lures need turning until the epoxy stops sagging
    • No maker page found for working time or safety notes; sold by Jamlyn-Supply, a third-party seller, at the time of writing

    Who should buy it

    Crankbait builders who want a high-build, glossy top coat and can turn baits while it levels.

    Check on Amazon

    • Type: two-part pour-on epoxy (listing)
    • Mix ratio: 1:1, equal amounts (listing)
    • Cure: 8 hours; full hardness in about 72 hours (listing)
    • Working time: not published
    • Price tier: $$ (live price above)

    Devcon 2 Ton Epoxy, 30-Minute Glue Epoxy

    30-Minute Glue Epoxy
    Devcon Epoxy, 2 Ton Epoxy, 4-1/2 Ounce Bottles, 2 Bottles

    Devcon 2 Ton

    Two 4.5 oz Bottles

    Builders who coat a few baits at a time and want one epoxy for gluing and top coating.

    $21.14 from AmazonAs of Nov 19, 00:08 UTC

    Verdict

    A 30-minute glue epoxy some long-time builders use as a top coat.

    Evidence: No independent test; maker specs. Source: Amazon listing.

    The listing says it “Sets in 30 minutes with strength up to 2,500 pounds per square inch” and “Dries clear.” On TackleUnderground, poster BobP writes: “I use Devcon Two Ton. Started with it many years ago and never saw a reason to change.” He rotates lures until it stops sagging, “about an hour.” Poster fishnart, who moved to ArtResin, wrote: “I can do 15 baits vs 2 with Devcon.”

    Devcon 2 Ton or Bob Smith Slow-Cure? Both are 30-minute glue epoxies. Devcon has the forum history; Bob Smith publishes its mix ratio and is the one Salty’s sells as a lure top coat.

    Specs (linked: two 4.5 oz bottles)

      Pros

      • Builders on TackleUnderground report years of use as a top coat
      • Dries clear and water resistant, per the listing

      Cons

      • Sets in 30 minutes, so fewer baits per batch, per one poster
      • Sold by Shop With Cents, a third-party seller, when checked

      Who should buy it

      Builders who coat a few baits at a time and want one epoxy for gluing and top coating.

      Check on Amazon

      • Set: 30 minutes (listing)
      • Strength: up to 2,500 psi (listing)
      • Mix ratio and full cure: not published on the listing
      • Price tier: $$ (live price above)

      Bob Smith Industries Slow-Cure Epoxy, 30-Minute Bulk Epoxy

      30-Minute Bulk Epoxy
      Bob Smith 206 Slow-Cure 9oz Epoxy

      Bob Smith Slow-Cure

      9 oz

      Saltwater plug builders who coat lures in batches and want a waterproof brush-on epoxy.

      $22.45 from AmazonAs of Nov 19, 00:08 UTC

      Verdict

      The 30-minute epoxy a lure-supply shop sells as its saltwater top coat.

      Evidence: Retailer review (sells it), not independent. Salty’s (saltwaterplugs.com): Bob Smith 30 minute epoxy, 4.5 oz and 9 oz.

      Bob Smith Industries calls Slow-Cure “an equal two-part hobby adhesive” that “has the highest strength of our epoxies. It is waterproof and more heat resistant.” It asks for temperatures “above 70°F.” Salty’s, which sells it, writes: “The BSI Epoxy is in our opinion the most durable coating you can use on a saltwater lure!” and rates the 9 oz at “approximately 30-40 lures.” Salty’s turns lures “3-4 times in first half hour.”

      Specs (linked: BSI-206, 9 oz combined)

        Pros

        • Waterproof 30-minute epoxy its maker rates as its strongest
        • 9 oz covers about 30-40 lures, per Salty’s

        Cons

        • Bob Smith publishes no yellowing claim, and the durability praise comes from a shop that sells it
        • Low stock and a third-party seller (Level_Brands) at the time of writing

        Who should buy it

        Saltwater plug builders who coat lures in batches and want a waterproof brush-on epoxy.

        Check on Amazon

        • Mix ratio: equal parts (maker)
        • Working time: 30 minutes (Salty’s)
        • Cure: overnight for bonding (maker)
        • UV / yellowing: not published
        • Price tier: $ (live price above)

        Alumilite Amazing Clear Cast Plus, UV-Resistant Pour Epoxy

        UV-Resistant Pour Epoxy
        Alumilite Amazing Clear Cast Plus 16 Oz, UV Resistant Epoxy…

        Amazing Clear Cast Plus

        16 oz Kit

        Builders who brush epoxy on painted crankbaits and want a published spec sheet and a UV-resistant formula.

        View on Amazon

        Verdict

        The UV-resistant version of the Alumilite epoxy a crankbait maker likely uses.

        Evidence: Independently reviewed, same series. Slim Shady Customs: “Amazingly Clear” by Alumilite (likely original Amazing Clear Cast), kit size not stated.

        Citing a 17-month sun-exposure comparison, Slim Shady Customs wrote: “I decided to use “Amazingly Clear” by Alumilite,” likely the original Amazing Clear Cast. The Plus version keeps the 1:1 mix, per Alumilite’s data sheet, with what Alumilite calls “industry-leading UV resistance,” a working time of 20-25 minutes and full cure in 3-5 days. Alumilite’s own caveat: “ACC+ will develop a yellow hue over time,” and it is “not intended for permanent outdoor use or direct UV exposure.” It asks for gloves, safety glasses and a well-ventilated room.

        Specs (linked: 16 fl oz kit)

          Pros

          • UV inhibitors meant to slow yellowing, per Alumilite
          • A full technical data sheet with working, tack-free and cure times

          Cons

          • The lure maker’s account covers the original formula, not Plus
          • Alumilite says it will still yellow over time; sold by Hyatt’s All Things Creative, with Alumilite also offering it, at the time of writing

          Who should buy it

          Builders who brush epoxy on painted crankbaits and want a published spec sheet and a UV-resistant formula.

          Check on Amazon

          • Mix ratio: 1:1 by weight or volume (maker)
          • Working time: 20-25 minutes at 70°F (maker)
          • Tack free: 24-48 hours; full cure: 3-5 days (maker)
          • Hardness: 75-D (maker)
          • Price tier: $$ (live price above)

          KBS DiamondFinish Clear, One-Part Dipping Clear

          One-Part Dipping Clear
          KBS Coatings 8404 DiamondFinish Watercolor Clear Coat - 1…

          KBS DiamondFinish Clear

          1 Quart

          Builders who dip many crankbaits or jigs and can let them hang for a week.

          $65.00 from AmazonAs of Nov 19, 00:08 UTC

          Verdict

          A one-part clear coat its maker shows how to dip lures in.

          Evidence: Independently reviewed, same series. Slim Shady Customs: KBS Diamond Finish Clear Coat, can size not stated.

          KBS calls it “a one-part moisture-cured urethane” with “no hardener or activator to mix and no pot life.” Its lure-dipping page says to dip at least twice, 2-4 hours apart; it “can be handled after 1 day and reaches full cure in at least 7 days,” and UV or bake lights should not be used to hurry it. The listing reports 1,000 hours of QUV 313B weathering “without yellowing, chalking, cracking or peeling.” Slim Shady Customs dips whole baits, bill included: “I have a fair amount of experience using KBS, and I believe that it is superior to 2-part epoxy in several areas.” His caveats: a lacquer coat first or the paint may run, worse fumes than epoxy, and jigs fished before full cure “were coming up chipped.”

          Specs (linked: 1 quart, 32 fl oz)

            Pros

            • Nothing to mix, so you pour out what a session needs
            • Sold and shipped by Amazon.com at the time of writing

            Cons

            • A week to full cure, and longer in cold rooms, per Slim Shady
            • Stronger fumes than epoxy, per Slim Shady; KBS asks for “good ventilation”

            Who should buy it

            Builders who dip many crankbaits or jigs and can let them hang for a week.

            Check on Amazon

            • Type: one-part moisture-cure urethane (listing)
            • Recoat: 2-4 hours (maker)
            • Full cure: 7 days or more (maker)
            • Weathering: QUV 313B, 1,000 hours (listing)
            • Price tier: $$ (live price above)

            ArtResin Epoxy Resin, 45-Minute Art Epoxy

            45-Minute Art Epoxy
            ArtResin Epoxy Resin – High-Gloss Clear Coat for Artwork…

            ArtResin

            8 oz Kit

            Builders who coat a dozen or more baits per session and want time to work.

            $28.00 from AmazonAs of Nov 19, 00:08 UTC

            Verdict

            An art epoxy with a long working time that TackleUnderground posters moved to from Devcon.

            Evidence: No independent test; maker specs. Source: ArtResin (maker).

            ArtResin lists a 1:1 mix by volume, “a working time of about 45 minutes,” dry to the touch in about 24 hours and full cure in 72 hours. It says ArtResin “meets ASTM D-4236 standards,” and recommends gloves, a well-ventilated room and a respirator “If ventilation is limited.” On TackleUnderground in 2016, poster fishnart wrote: “I’ve totally switched over to the new Art Resin.” Poster nedyarb described about 40 casts and throws at a wall without visible damage to a coated crankbait; fishnart and poster law651 noted it had not yet seen any water.

            Specs (linked: 8 oz kit, 4 oz resin + 4 oz hardener)

              Pros

              • Longer working time than the 30-minute epoxies, so more baits per batch
              • Sold by ArtResin’s own storefront at the time of writing

              Cons

              • An art resin; lure reports are 2016 forum posts
              • The maker suggests 75-85°F, warmer than many garages

              Who should buy it

              Builders who coat a dozen or more baits per session and want time to work.

              Check on Amazon

              • Mix ratio: 1:1 by volume (maker)
              • Working time: about 45 minutes (maker)
              • Cure: 72 hours (maker)
              • Price tier: $$ (live price above)

              Alumilite Alumi-UV, UV-Cure Lure Resin

              UV-Cure Lure Resin
              Alumilite Alumi-UV 4 Oz, Light Cured Resin for Fishing Lure…

              Alumi-UV

              4 oz

              Jig and small-lure makers who want eyes and heads sealed in minutes.

              $14.99 from AmazonAs of Nov 19, 00:08 UTC

              Verdict

              A UV-cure resin its maker sells by name for fishing lures.

              Evidence: No independent test; maker specs. Source: Alumilite (maker).

              Alumilite titles it “Light Cured Resin for Fishing Lure and Ring Making” and says UV resin “is ideal for precise crafts such as fishing lures,” hardening “in minutes under UV or natural sunlight.” The listing’s chart gives 2-10 minutes and no mixing. Alumilite advises curing both sides and adding a thin top layer if the surface stays tacky. On Alumilite’s own site (maker-hosted reviews, not independent), one buyer writes “I use it on all of our hand tied fishing jigs,” and another reports no yellowing in direct sun.

              Alumi-UV or Loon UV Fly Finish? Both are one-part UV resins. Alumi-UV is a 4 oz bottle sold for lures; Loon is a water-thin 1/2 oz with a needle for flies.

              Specs (linked: 4 oz bottle)

                Pros

                • Cures in 2-10 minutes under UV with nothing to mix, per the listing
                • Sold by Alumilite’s own storefront at the time of writing

                Cons

                • Needs a UV lamp or direct sun, and Alumilite says larger pieces need curing from both sides
                • A 4 oz bottle, beside 8-32 oz epoxy kits

                Who should buy it

                Jig and small-lure makers who want eyes and heads sealed in minutes.

                Check on Amazon

                • Mix: none (maker)
                • Cure: 2-10 minutes under UV (listing)
                • UV / yellowing: not published
                • Price tier: $ (live price above)

                Loon UV Clear Fly Finish, Thin UV Fly Finish

                Thin UV Fly Finish
                Loon Outdoors UV CLEAR FLY FINISH, Flow, 1/2 oz

                Loon UV Clear Fly Finish

                Flow 1/2 oz

                Fly tiers who want thread wraps and small heads sealed in seconds.

                $19.95 from AmazonAs of Nov 19, 00:08 UTC

                Verdict

                A water-thin UV finish for fly heads, from a fly-tying maker.

                Evidence: No independent test; maker specs. Source: Loon Outdoors (maker).

                Loon Outdoors describes the Flow formula as “Water-thin for locking threads and coating small flies.” It “Instantly cures with sunlight or UV light,” and “In direct sun (or when using Loon’s UV lights) hardening should take approximately 15 seconds.”

                Specs (linked: Flow, 1/2 oz)

                  Pros

                  • Thin enough to lock thread wraps on small flies
                  • Small bottle with a needle for precise work

                  Cons

                  • A 1/2 oz bottle for fly heads, too small for coating crankbaits
                  • Sold by The Kingfisher, a third-party seller, at the time of writing

                  Who should buy it

                  Fly tiers who want thread wraps and small heads sealed in seconds.

                  Check on Amazon

                  • Mix: none (maker)
                  • Cure: about 15 seconds in direct sun or under a Loon UV light (maker)
                  • Applicator: UV-blocking needle (maker)
                  • Price tier: $ (live price above)

                  Two-Part Epoxy, UV Resin or One-Part Clear Coat?

                  High build and cure time

                  Two-part coating epoxies such as EnviroTex Lite, ArtResin and Amazing Clear Cast Plus go on as one thick coat but list 72 hours or more to full cure, and the lure has to turn while the epoxy levels: “a couple of hours” for coating epoxies, per TackleUnderground’s BobP. Slim Shady Customs warns that too thick a coat can change how a crankbait runs; for divers, see our deep-diving crankbait rods. Thread posters warn against 5-minute epoxy: “you inevitably end up with a lumpy mess.”

                  UV-cure resin

                  UV resins have no mix and cure in seconds to minutes under a lamp or sun, per Alumilite and Loon: a fit for eyes, jig heads and flies.

                  One-part clear coat for dipping

                  A one-part clear coat such as KBS DiamondFinish needs no mixing, so it suits dipping; with epoxy, Slim Shady notes, you would have to mix a large batch and throw the rest away. The trade-off is a week or more to full cure and stronger fumes.

                  Yellowing and UV resistance

                  Alumilite says yellowing comes “As with all epoxy chemistry,” and that even its UV-resistant Plus formula “will develop a yellow hue over time.” KBS cites a QUV 313B weathering test for DiamondFinish. Alumilite’s advice is to keep finished pieces out of direct sunlight.

                  Gloves and ventilation

                  Read each maker’s safety data sheet. Alumilite asks for gloves and safety glasses; ArtResin for gloves, a ventilated room and a respirator where airflow is limited; KBS for good ventilation; Salty’s for rubber gloves when coating. The same epoxy skills apply to rod guides; see our rod repair guide.

                  Frequently Asked Questions

                  Q. Is it better to use UV resin or epoxy resin?

                  It depends on the job. Alumilite, which makes both, puts UV resin on “precise crafts such as fishing lures” and two-part epoxy on “larger, rugged items like coasters and trays.” UV resin cures in seconds to minutes under a lamp or sun, per Alumilite and Loon; a two-part coating epoxy goes on as one thick coat but lists 72 hours or more to full cure.

                  Q. What epoxy do professionals use?

                  Among the lure builders we read: Slim Shady Customs uses Alumilite’s “Amazingly Clear” and KBS DiamondFinish, Salty’s sells Bob Smith 30-minute epoxy as its top coat, and TackleUnderground builders name Devcon 2 Ton, EnviroTex Lite and ArtResin. None of them describes a side-by-side test.

                  Q. What is the strongest waterproof epoxy?

                  No source we read compares strength across brands. Bob Smith Industries says Slow-Cure “has the highest strength of our epoxies. It is waterproof and more heat resistant.” The Devcon 2 Ton listing gives up to 2,500 psi. Those claims cover each maker’s own range.

                  Q. Which brand of resin epoxy is considered the best?

                  No source we read ranks brands. In the TackleUnderground thread, builders split between EnviroTex Lite, Devcon 2 Ton, Bob Smith and ArtResin, and each names a trade-off: runny, quick to set, or not yet proven in the water.

                  The bottom line

                  Final Verdict

                  Brush-on crankbait top coat: the EnviroTex Lite Pour-On High Gloss Finish (check price), the ArtResin Epoxy Resin (check price) for more working time, or the Alumilite Amazing Clear Cast Plus (check price) for a UV-resistant formula. Thirty-minute epoxy: the Bob Smith Industries Slow-Cure Epoxy (check price) for saltwater batches or the Devcon 2 Ton Epoxy (check price) for a few baits. Dipping: the KBS DiamondFinish Clear (check price). Jigs in minutes: the Alumilite Alumi-UV (check price); fly heads: the Loon UV Clear Fly Finish (check price).

                  Product prices and availability are accurate as of the date/time indicated and are subject to change. Any price and availability information displayed on Amazon.com at the time of purchase will apply to the purchase of this product.

                  Outgearly Team
                  Outgearly Team

                  Written and reviewed by the Outgearly Team. See the About page for how we work.