The short answer
For a brush-on crankbait top coat, EnviroTex Lite Pour-On High Gloss Finish; for dipping many baits with nothing to mix, KBS DiamondFinish Clear; for a fast cure on jigs and small parts, Alumilite Alumi-UV.
Our verdict
Lure Epoxy Top Picks
A painted crankbait or jig needs a clear top coat for a hard, glossy shell. Lure builders use three kinds: two-part epoxies you brush on, UV-cure resins that harden under a lamp or sunlight, and one-part clear coats you dip. Here are eight from seven brands, each linked at the exact size, with the cure time, working time and mix ratio its maker or listing gives. For finished baits, see our guide to freshwater lures by type, and for rods and reels, browse our fishing gear guides.
Related guide: Best Gear for Trout Fishing: Rod, Reel, Line, Lures and Net
Lure coating finder
Find a top coat for the lures you build
Pick what you are coating and a price tier per container. The suggestion is our editorial starting point among the eight coatings below, drawn from the makers' pages and the sources cited in each review, not a test result.
Tiers are relative to the products in this guide; live prices are in the comparison table below.
Compare the picks
Compare the 8 Lure Top Coats
EnviroTex LitePour-On Epoxy Top CoatCrankbaits, brush-onListing: about 72 hours$24.80
Evidence: listing specs; TackleUnderground owner posts cited in the review
Devcon 2 Ton30-Minute Glue EpoxyCrankbaits, brush-onListing: sets in 30 minutes$21.14
Evidence: listing specs; TackleUnderground owner posts cited in the review
Bob Smith Slow-Cure30-Minute Bulk EpoxySaltwater lures, brush-onMaker: overnight$22.45
Evidence: Salty's (saltwaterplugs.com) (a retailer), not independent
Amazing Clear Cast PlusUV-Resistant Pour EpoxyCrankbaits, brush-onMaker: 3-5 days
Evidence: Slim Shady Customs, Alumilite “Amazingly Clear” (likely the original Amazing Clear Cast), not the Plus formula
KBS DiamondFinish ClearOne-Part Dipping ClearDipping, jigs, crankbaitsMaker: 7 days$65.00 Prime
Evidence: Slim Shady Customs, DiamondFinish Clear; can size not stated
ArtResin45-Minute Art EpoxyCrankbaits, brush-onMaker: 72 hours$28.00
Evidence: maker specs; 2016 TackleUnderground owner posts cited in the review
Alumi-UVUV-Cure Lure ResinJigs, uV cure, small batchesListing: 2-10 minutes$14.99
Evidence: maker specs only, no independent test
Loon UV Clear Fly FinishThin UV Fly FinishFly heads, uV cureMaker: about 15 seconds$19.95
Evidence: maker specs only, no independent test
“Not published”: neither the maker nor the Amazon listing we read gives the figure. Cure times are the makers’ own and change with temperature and coat thickness.
How We Chose These Lure Coatings
How this guide was built
built from manufacturer documentation, published third-party reviews and owner reports; we have not tested these products ourselves.
What each coating had to show
- A lure-making tie: sold for lures by its maker, or used as a top coat by a named lure builder or supplier.
- The exact size on one Amazon listing, new and in stock on the day of writing.
- Working and cure figures from the maker or listing, or “not published.”
- A distinct job: brush-on, dip-on or UV-cure, with a stated trade-off where two overlap.
Sources and their limits
Sources and their limits
Figures come from the makers’ pages and technical data sheets, then the Amazon listings, each labelled. Lure-making context comes from Slim Shady Customs, a custom crankbait maker; Salty’s, a lure-supply shop that sells Bob Smith epoxy (a retailer, not independent); and a 2016 TackleUnderground thread of lure builders. None compared these products side by side. Five of the eight were sold on Amazon by third-party sellers when we checked; each review names the seller.
Lure Epoxies and Clear Coats: Detailed Reviews
Picks: EnviroTex Lite, Devcon 2 Ton, Bob Smith Slow-Cure, Amazing Clear Cast Plus, KBS DiamondFinish, ArtResin, Alumi-UV, Loon UV Fly Finish.
EnviroTex Lite Pour-On High Gloss Finish, Pour-On Epoxy Top Coat
Crankbait builders who want a high-build, glossy top coat and can turn baits while it levels.
$24.80 from AmazonAs of Nov 19, 00:08 UTCVerdict
The pour-on coating epoxy TackleUnderground posters keep naming for crankbait top coats.
Evidence: No independent test; maker specs. Source: Amazon listing.
The Amazon listing sells it as a thick single coat: “No need to apply 60 coats of varnish,” it says, and “It cures in 8 hours and reaches full strength and hardness in about 72 hours.” In the TackleUnderground thread, poster mcallister920 writes “Envirotex Lite- the search stops there,” and poster Travis calls it “readily available” and “isn’t too difficult to use.” Poster token12 adds the caveat: “E-tex in my opinion is runny,” with “about 8 hours to harden and 48-72 hours for a full cure.”
EnviroTex Lite, ArtResin or Amazing Clear Cast Plus? All three are 1:1 coating epoxies. EnviroTex Lite has the lure-forum following; ArtResin lists about 45 minutes of working time; Amazing Clear Cast Plus publishes a full data sheet and a UV-resistant formula.
Specs (linked: 16 oz kit)
Pros
- One thick coat in place of many coats of varnish, per the listing
- Named by several TackleUnderground lure builders
Cons
- Runny, per one poster; poster BobP says coated lures need turning until the epoxy stops sagging
- No maker page found for working time or safety notes; sold by Jamlyn-Supply, a third-party seller, at the time of writing
Who should buy it
Crankbait builders who want a high-build, glossy top coat and can turn baits while it levels.
- Type: two-part pour-on epoxy (listing)
- Mix ratio: 1:1, equal amounts (listing)
- Cure: 8 hours; full hardness in about 72 hours (listing)
- Working time: not published
- Price tier: $$ (live price above)
Devcon 2 Ton Epoxy, 30-Minute Glue Epoxy
Builders who coat a few baits at a time and want one epoxy for gluing and top coating.
$21.14 from AmazonAs of Nov 19, 00:08 UTCVerdict
A 30-minute glue epoxy some long-time builders use as a top coat.
Evidence: No independent test; maker specs. Source: Amazon listing.
The listing says it “Sets in 30 minutes with strength up to 2,500 pounds per square inch” and “Dries clear.” On TackleUnderground, poster BobP writes: “I use Devcon Two Ton. Started with it many years ago and never saw a reason to change.” He rotates lures until it stops sagging, “about an hour.” Poster fishnart, who moved to ArtResin, wrote: “I can do 15 baits vs 2 with Devcon.”
Devcon 2 Ton or Bob Smith Slow-Cure? Both are 30-minute glue epoxies. Devcon has the forum history; Bob Smith publishes its mix ratio and is the one Salty’s sells as a lure top coat.
Specs (linked: two 4.5 oz bottles)
Pros
- Builders on TackleUnderground report years of use as a top coat
- Dries clear and water resistant, per the listing
Cons
- Sets in 30 minutes, so fewer baits per batch, per one poster
- Sold by Shop With Cents, a third-party seller, when checked
Who should buy it
Builders who coat a few baits at a time and want one epoxy for gluing and top coating.
- Set: 30 minutes (listing)
- Strength: up to 2,500 psi (listing)
- Mix ratio and full cure: not published on the listing
- Price tier: $$ (live price above)
Bob Smith Industries Slow-Cure Epoxy, 30-Minute Bulk Epoxy
Saltwater plug builders who coat lures in batches and want a waterproof brush-on epoxy.
$22.45 from AmazonAs of Nov 19, 00:08 UTCVerdict
The 30-minute epoxy a lure-supply shop sells as its saltwater top coat.
Evidence: Retailer review (sells it), not independent. Salty’s (saltwaterplugs.com): Bob Smith 30 minute epoxy, 4.5 oz and 9 oz.
Bob Smith Industries calls Slow-Cure “an equal two-part hobby adhesive” that “has the highest strength of our epoxies. It is waterproof and more heat resistant.” It asks for temperatures “above 70°F.” Salty’s, which sells it, writes: “The BSI Epoxy is in our opinion the most durable coating you can use on a saltwater lure!” and rates the 9 oz at “approximately 30-40 lures.” Salty’s turns lures “3-4 times in first half hour.”
Specs (linked: BSI-206, 9 oz combined)
Pros
- Waterproof 30-minute epoxy its maker rates as its strongest
- 9 oz covers about 30-40 lures, per Salty’s
Cons
- Bob Smith publishes no yellowing claim, and the durability praise comes from a shop that sells it
- Low stock and a third-party seller (Level_Brands) at the time of writing
Who should buy it
Saltwater plug builders who coat lures in batches and want a waterproof brush-on epoxy.
- Mix ratio: equal parts (maker)
- Working time: 30 minutes (Salty’s)
- Cure: overnight for bonding (maker)
- UV / yellowing: not published
- Price tier: $ (live price above)
Alumilite Amazing Clear Cast Plus, UV-Resistant Pour Epoxy
Builders who brush epoxy on painted crankbaits and want a published spec sheet and a UV-resistant formula.
View on AmazonVerdict
The UV-resistant version of the Alumilite epoxy a crankbait maker likely uses.
Evidence: Independently reviewed, same series. Slim Shady Customs: “Amazingly Clear” by Alumilite (likely original Amazing Clear Cast), kit size not stated.
Citing a 17-month sun-exposure comparison, Slim Shady Customs wrote: “I decided to use “Amazingly Clear” by Alumilite,” likely the original Amazing Clear Cast. The Plus version keeps the 1:1 mix, per Alumilite’s data sheet, with what Alumilite calls “industry-leading UV resistance,” a working time of 20-25 minutes and full cure in 3-5 days. Alumilite’s own caveat: “ACC+ will develop a yellow hue over time,” and it is “not intended for permanent outdoor use or direct UV exposure.” It asks for gloves, safety glasses and a well-ventilated room.
Specs (linked: 16 fl oz kit)
Pros
- UV inhibitors meant to slow yellowing, per Alumilite
- A full technical data sheet with working, tack-free and cure times
Cons
- The lure maker’s account covers the original formula, not Plus
- Alumilite says it will still yellow over time; sold by Hyatt’s All Things Creative, with Alumilite also offering it, at the time of writing
Who should buy it
Builders who brush epoxy on painted crankbaits and want a published spec sheet and a UV-resistant formula.
- Mix ratio: 1:1 by weight or volume (maker)
- Working time: 20-25 minutes at 70°F (maker)
- Tack free: 24-48 hours; full cure: 3-5 days (maker)
- Hardness: 75-D (maker)
- Price tier: $$ (live price above)
KBS DiamondFinish Clear, One-Part Dipping Clear
Builders who dip many crankbaits or jigs and can let them hang for a week.
$65.00 from AmazonAs of Nov 19, 00:08 UTCVerdict
A one-part clear coat its maker shows how to dip lures in.
Evidence: Independently reviewed, same series. Slim Shady Customs: KBS Diamond Finish Clear Coat, can size not stated.
KBS calls it “a one-part moisture-cured urethane” with “no hardener or activator to mix and no pot life.” Its lure-dipping page says to dip at least twice, 2-4 hours apart; it “can be handled after 1 day and reaches full cure in at least 7 days,” and UV or bake lights should not be used to hurry it. The listing reports 1,000 hours of QUV 313B weathering “without yellowing, chalking, cracking or peeling.” Slim Shady Customs dips whole baits, bill included: “I have a fair amount of experience using KBS, and I believe that it is superior to 2-part epoxy in several areas.” His caveats: a lacquer coat first or the paint may run, worse fumes than epoxy, and jigs fished before full cure “were coming up chipped.”
Specs (linked: 1 quart, 32 fl oz)
Pros
- Nothing to mix, so you pour out what a session needs
- Sold and shipped by Amazon.com at the time of writing
Cons
- A week to full cure, and longer in cold rooms, per Slim Shady
- Stronger fumes than epoxy, per Slim Shady; KBS asks for “good ventilation”
Who should buy it
Builders who dip many crankbaits or jigs and can let them hang for a week.
- Type: one-part moisture-cure urethane (listing)
- Recoat: 2-4 hours (maker)
- Full cure: 7 days or more (maker)
- Weathering: QUV 313B, 1,000 hours (listing)
- Price tier: $$ (live price above)
ArtResin Epoxy Resin, 45-Minute Art Epoxy
Builders who coat a dozen or more baits per session and want time to work.
$28.00 from AmazonAs of Nov 19, 00:08 UTCVerdict
An art epoxy with a long working time that TackleUnderground posters moved to from Devcon.
Evidence: No independent test; maker specs. Source: ArtResin (maker).
ArtResin lists a 1:1 mix by volume, “a working time of about 45 minutes,” dry to the touch in about 24 hours and full cure in 72 hours. It says ArtResin “meets ASTM D-4236 standards,” and recommends gloves, a well-ventilated room and a respirator “If ventilation is limited.” On TackleUnderground in 2016, poster fishnart wrote: “I’ve totally switched over to the new Art Resin.” Poster nedyarb described about 40 casts and throws at a wall without visible damage to a coated crankbait; fishnart and poster law651 noted it had not yet seen any water.
Specs (linked: 8 oz kit, 4 oz resin + 4 oz hardener)
Pros
- Longer working time than the 30-minute epoxies, so more baits per batch
- Sold by ArtResin’s own storefront at the time of writing
Cons
- An art resin; lure reports are 2016 forum posts
- The maker suggests 75-85°F, warmer than many garages
Who should buy it
Builders who coat a dozen or more baits per session and want time to work.
- Mix ratio: 1:1 by volume (maker)
- Working time: about 45 minutes (maker)
- Cure: 72 hours (maker)
- Price tier: $$ (live price above)
Alumilite Alumi-UV, UV-Cure Lure Resin
Jig and small-lure makers who want eyes and heads sealed in minutes.
$14.99 from AmazonAs of Nov 19, 00:08 UTCVerdict
A UV-cure resin its maker sells by name for fishing lures.
Evidence: No independent test; maker specs. Source: Alumilite (maker).
Alumilite titles it “Light Cured Resin for Fishing Lure and Ring Making” and says UV resin “is ideal for precise crafts such as fishing lures,” hardening “in minutes under UV or natural sunlight.” The listing’s chart gives 2-10 minutes and no mixing. Alumilite advises curing both sides and adding a thin top layer if the surface stays tacky. On Alumilite’s own site (maker-hosted reviews, not independent), one buyer writes “I use it on all of our hand tied fishing jigs,” and another reports no yellowing in direct sun.
Alumi-UV or Loon UV Fly Finish? Both are one-part UV resins. Alumi-UV is a 4 oz bottle sold for lures; Loon is a water-thin 1/2 oz with a needle for flies.
Specs (linked: 4 oz bottle)
Pros
- Cures in 2-10 minutes under UV with nothing to mix, per the listing
- Sold by Alumilite’s own storefront at the time of writing
Cons
- Needs a UV lamp or direct sun, and Alumilite says larger pieces need curing from both sides
- A 4 oz bottle, beside 8-32 oz epoxy kits
Who should buy it
Jig and small-lure makers who want eyes and heads sealed in minutes.
- Mix: none (maker)
- Cure: 2-10 minutes under UV (listing)
- UV / yellowing: not published
- Price tier: $ (live price above)
Loon UV Clear Fly Finish, Thin UV Fly Finish
Fly tiers who want thread wraps and small heads sealed in seconds.
$19.95 from AmazonAs of Nov 19, 00:08 UTCVerdict
A water-thin UV finish for fly heads, from a fly-tying maker.
Evidence: No independent test; maker specs. Source: Loon Outdoors (maker).
Loon Outdoors describes the Flow formula as “Water-thin for locking threads and coating small flies.” It “Instantly cures with sunlight or UV light,” and “In direct sun (or when using Loon’s UV lights) hardening should take approximately 15 seconds.”
Specs (linked: Flow, 1/2 oz)
Pros
- Thin enough to lock thread wraps on small flies
- Small bottle with a needle for precise work
Cons
- A 1/2 oz bottle for fly heads, too small for coating crankbaits
- Sold by The Kingfisher, a third-party seller, at the time of writing
Who should buy it
Fly tiers who want thread wraps and small heads sealed in seconds.
- Mix: none (maker)
- Cure: about 15 seconds in direct sun or under a Loon UV light (maker)
- Applicator: UV-blocking needle (maker)
- Price tier: $ (live price above)
Two-Part Epoxy, UV Resin or One-Part Clear Coat?
High build and cure time
Two-part coating epoxies such as EnviroTex Lite, ArtResin and Amazing Clear Cast Plus go on as one thick coat but list 72 hours or more to full cure, and the lure has to turn while the epoxy levels: “a couple of hours” for coating epoxies, per TackleUnderground’s BobP. Slim Shady Customs warns that too thick a coat can change how a crankbait runs; for divers, see our deep-diving crankbait rods. Thread posters warn against 5-minute epoxy: “you inevitably end up with a lumpy mess.”
UV-cure resin
UV resins have no mix and cure in seconds to minutes under a lamp or sun, per Alumilite and Loon: a fit for eyes, jig heads and flies.
One-part clear coat for dipping
A one-part clear coat such as KBS DiamondFinish needs no mixing, so it suits dipping; with epoxy, Slim Shady notes, you would have to mix a large batch and throw the rest away. The trade-off is a week or more to full cure and stronger fumes.
Yellowing and UV resistance
Alumilite says yellowing comes “As with all epoxy chemistry,” and that even its UV-resistant Plus formula “will develop a yellow hue over time.” KBS cites a QUV 313B weathering test for DiamondFinish. Alumilite’s advice is to keep finished pieces out of direct sunlight.
Gloves and ventilation
Read each maker’s safety data sheet. Alumilite asks for gloves and safety glasses; ArtResin for gloves, a ventilated room and a respirator where airflow is limited; KBS for good ventilation; Salty’s for rubber gloves when coating. The same epoxy skills apply to rod guides; see our rod repair guide.
Frequently Asked Questions
Q. Is it better to use UV resin or epoxy resin?
It depends on the job. Alumilite, which makes both, puts UV resin on “precise crafts such as fishing lures” and two-part epoxy on “larger, rugged items like coasters and trays.” UV resin cures in seconds to minutes under a lamp or sun, per Alumilite and Loon; a two-part coating epoxy goes on as one thick coat but lists 72 hours or more to full cure.
Q. What epoxy do professionals use?
Among the lure builders we read: Slim Shady Customs uses Alumilite’s “Amazingly Clear” and KBS DiamondFinish, Salty’s sells Bob Smith 30-minute epoxy as its top coat, and TackleUnderground builders name Devcon 2 Ton, EnviroTex Lite and ArtResin. None of them describes a side-by-side test.
Q. What is the strongest waterproof epoxy?
No source we read compares strength across brands. Bob Smith Industries says Slow-Cure “has the highest strength of our epoxies. It is waterproof and more heat resistant.” The Devcon 2 Ton listing gives up to 2,500 psi. Those claims cover each maker’s own range.
Q. Which brand of resin epoxy is considered the best?
No source we read ranks brands. In the TackleUnderground thread, builders split between EnviroTex Lite, Devcon 2 Ton, Bob Smith and ArtResin, and each names a trade-off: runny, quick to set, or not yet proven in the water.
The bottom line
Final Verdict
Brush-on crankbait top coat: the EnviroTex Lite Pour-On High Gloss Finish (check price), the ArtResin Epoxy Resin (check price) for more working time, or the Alumilite Amazing Clear Cast Plus (check price) for a UV-resistant formula. Thirty-minute epoxy: the Bob Smith Industries Slow-Cure Epoxy (check price) for saltwater batches or the Devcon 2 Ton Epoxy (check price) for a few baits. Dipping: the KBS DiamondFinish Clear (check price). Jigs in minutes: the Alumilite Alumi-UV (check price); fly heads: the Loon UV Clear Fly Finish (check price).
Product prices and availability are accurate as of the date/time indicated and are subject to change. Any price and availability information displayed on Amazon.com at the time of purchase will apply to the purchase of this product.
